Design of 5V PWM to 0-10VDC analog output circuit to drive VFD

₹600-1500 INR

Zaprt

Objavljeno

pred več kot 8 leti

₹600-1500 INR

Plačilo ob dostavi

We are using ATMEGA2560 and already using some circuit to convert 5V PWM to 0-10VDC analog output circuit. It works fine on no load and no normal environment. If we use this circuit to drive VFD in a industrial noise environment, then there is voltage drop on the analog output. The 10V drops to 7V. We need a reliable circuit to convert 5V PWM to 0-10VDC analog output circuit to drive VFD in a industrial environment.

ID projekta: 8848965

Več o projektu

14 ponudb

Projekt na daljavo

Aktivno pred 8 leti

Želite zaslužiti?

E-naslov

Prednosti oddajanja ponudb na Freelancerju

Nastavite svoj proračun in časovni okvir

Prejmite plačilo za svoje delo

Povzetek predloga

Registracija in oddajanje ponudb sta brezplačna

14 freelancerjev je oddalo ponudbo s povprečno vrednostjo ₹1.526 INR za to delo

@htr1000

A proposal has not yet been provided

₹1.300 INR v 1 dnevu

4,7

(6 ocen)

2,4

@EngSolution

it can be solved by implementing some filtering and feed back. Are you using arduino ATMEGA2560 ? What is the distance between ATMEGA2560 board and VFD? Regards Tahir

₹3.333 INR v 5 dneh

5,0

(3 ocen)

2,1

@goharriz

Hello, I'm interested in your project, I have some questions: Could you upload the circuit you are using? Is there available any figure of the input impedance of the VFD? What happen if you test the circuit with the VFD in a non-industrial environment? I look forward to your reply. Thank you.

₹1.750 INR v 6 dneh

5,0

(3 ocen)

2,0

@sapna321

A proposal has not yet been provided

₹1.300 INR v 1 dnevu

5,0

(1 ocena)

1,6

@silviu233

Hi, I'm a responsible person who is serious in work.I also have work experience in electronic engineering

₹850 INR v 2 dneh

0,0

(0 ocen)

0,0

@Christianhaddad

Hello Sir, am ready to work on what are you asking am a micro electronics engineer and have support of some experts engineers in my area. i will be happy to help you once you give me more details Best regards, Chris

₹1.300 INR v 3 dneh

0,0

(0 ocen)

0,0

@dc786ribadiya

I am able to only provide you schematic and you need to test by your self because i am not available in india now. and I have not any setup with me. I am embedded Firmware Developer.

₹3.333 INR v 3 dneh

0,0

(0 ocen)

0,0

@murali1990

A proposal has not yet been provided

₹1.250 INR v 1 dnevu

0,0

(0 ocen)

0,0

@thomaslehuche

Your problem seems to be quite common. But we will need more information about the real environment and the power source(s) of your board.

₹1.500 INR v 3 dneh

0,0

(0 ocen)

0,0

@sheeljain28

Prefect circuit i will give you

₹1.250 INR v 5 dneh

0,0

(0 ocen)

0,0

@slec

Dear Employer, I have already done a project like this. I have designed and implemented a controlling system for industrially used transformer winding machine (see my portfolio) and it works properly. It has a 3-phase motor and an inverter (Fuji FVR-G7S-EX) to drive the motor. The inverter has an analog input to control the speed, normally it uses a potentiometer to vary the speed manually. I have designed a circuit convert digital PWM signal to the analog voltage to vary speed by the MCU. It also uses 0V to 10V. My circuit capable to driving motor lowest speed (0.6Hz) on zero duty cycle and highest speed (60Hz) on 255 duty cycle. I have used small no. of components available in a market. I have used MOSFET to get the maximum range of motor speed. I have used Opto-Coupler to isolate the microcontroller and inverter. It important to properly work micro-controller in a noisy environment without unwanted resets and error running. Actually I am sure that this circuit reliable and I hope to match you want. If you have any doubts don’t hesitate to contact me. I am a new member to FreeLancer. So if has some problems with communication sorry for these. And I like to do this job for the minimum cost. Thank you.

₹600 INR v 1 dnevu