Require a Sydney Australia based Electrical / Computer Engineer for contract work

min $50 AUD / hour

Zaprt

Objavljeno

pred približno 5 leti

min $50 AUD / hour

Looking for a qualified Electrical Engineer or Computer Engineer. Must have experience in Embedded Hardware development, debugging and fault finding and using test instruments. Must also have experience in how Embedded Software development works and collaborate with developers of PCB and / or firmware to load, debug and run sniffing and probes on hardware and serial lines where required in locations around Sydney. Hourly or weekly monthly rate for right candidate. Previous experience essential would suit freelancer with flexible times. Any experience in Embedded Software development, PCB Design, firmware writing in C, and/or proficient in reading / writing codes for 8/32 bits microcontrollers (Atmel/Microchip) is welcome. We may engage multiple people if one candidate is not flexible. A Non Disclosure agreement will be required to be signed to protect our IP. If you are qualified and ok with TnCs please apply asap Hourly Rate will vary based on experience and training required.

Electrical Engineering

ID projekta: 18993618

Več o projektu

5 ponudb

Projekt na daljavo

Aktivno pred 5 leti

Želite zaslužiti?

E-naslov

Prednosti oddajanja ponudb na Freelancerju

Nastavite svoj proračun in časovni okvir

Prejmite plačilo za svoje delo

Povzetek predloga

Registracija in oddajanje ponudb sta brezplačna

5 freelancerjev je oddalo ponudbo s povprečno vrednostjo $53 AUD/uro za to delo

@Tomorrow1201

Hi there. I offer you the services for circuit /PCB designs. I am designer expert with 10+ years of experience in Circuit designs, PCB designs, Zigbee/bluetooth,Wifi software development. You can check our designs in our portfolio. If you want, I will share more designs I completed so far through interview. So I like to discuss the job with you. Lets talk about your project through interview. Thank you.

$50 AUD v 40 dneh

4,3

(8 ocen)

4,8

@tommro

I'm an electronic engineer with more than 15 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC and ARM Cortex) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Microchip PIC (MPLAB X + XC compilers) and Eclipse + GNU ARM for different ARM Cortex M3/M4 manufacturers (STM32Fx, NXP, EFM32 SiLabs, but I'm ready to learn new frameworks). I work both single task and multi task environment (FreeRTOS and RTX). I write code both for low level driver (GPIO, UART, SPI, I2C, PWM....) management and for high level/final application. I work also in "C code" commercial boards Arduino/ESP8266 and Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. As SW developer, I work in C, C++, .NET, Java, and lot of others programming languages. Mainly I work for Windows O.S., but I have experience in Linux development too. I have experience in openCV library for image/video processing.

$55 AUD v 40 dneh

0,0

(0 ocen)

0,0

@vw8119435vw

Hello, my name is Lester Castro Capote, graduate of Engineering in automatic control at the Polytechnic University of Havana, Cuba, I live in Brazil and I have a lot of experience programming microcontrollers of the whole family of Microchip and Arduino boards, I have little experience in the hardware design but I have sufficient knowledge of analog and digital electronics to understand everything that happens at the level of ones and zeros. He was able to work up to 40 hours a week.

$50 AUD v 40 dneh